Contents

 Install DOS 6.22
 Procedure:
 Win 3.11

5/28/97 BJM

Install DOS 6.22

Assumptions:
*The files Autoexec.bat, Config.sys, System.ini, Win.ini, and
all needed device driveshave been copied onto a floppy or
other hard drive.
*All other needed and user files have also been backed up.
*Installer has copy of MS-DOS installation disk.


Warning! This procedure will remove all files on computer.
Check to make sure that this procedure is appropriate.


Procedure:


1) Reboot off of a bootable disk with the programs fdiskand
format(e.g. You can use MS-DOS installation disk).


2) Remove Disk Partition:
*Run fdisk: a:\>fdisk
If you booted off of MS-DOS Installation Disk, first exit from
Setup program (Press F3 twice).
*Delete disk partitions: Select 3, then select 1to delete the
primary partition. Press Enter twice, then enter the partition's
Volume Label (shown near the top) and then return. When
asked to confirm deletion, select y, then return, and then ESC.
*If the hard drive has an extended partition and/or a logical
drive (additional partitions will be listed near the top of the
screen), delete them also by selecting 3, then
2 (extended)or 3 (logical). When finished, hit ESC. The
computer will then reboot.


3) Reformat Disk and Install MS-DOS:
*After the computer reboots, press Enter for each section until
the computer reboots. The program will then reformat the disk.
*After the computer again reboots, press Enter for the next two
screens.
*After several files copy to the hard drive, press Enter for the
next two screens. The installation will then be finished.

5/28/97 BJM

Win 3.11

Assumptions:
*DOS has been installed on c: drive.
*Installer has copy of DOS\Windows Network Installation
Procedure and Standard Net Install disk from the Field Manual.


1) Edit or create config.sys file to change lastdrive value:
*Edit config.sys --c:\> edit config.sys
*Add or edit lastdrive line to read:lastdrive=e


2) Insert Standard Net Installdisk into drive a:and run the
Windows setup program:
c:\> a:
a:\> winsetup Card Type(e.g. winsetup 3c59x)


3) Install first set of files:
*After the Windows setup begins, press Enter.
*When prompted, enter your loginname and passwordfor
Novel server.
*Press enter until prompted for the type of setup; choose
Custom [C].
*Press enter for the next two sections, after which the program
will copy several files onto the hard drive.


4) Install second set of files:
*When asked for the Full nameand Product number, enter
the departmentof the user for the name and leave the
Product number empty.
*Press Enter for the next several sections. The program will then
copy additional files onto the hard drive.
*When the screen for printer setup appears, select Continue.


5) Install the Novel Network software:
*In the next window, which will be for Network Setup, select
Networks.
*In the new screen select Install Windows support for the
following network. Under this selection will be a list of
network software; choose
Novel Netware [Workstation Shell 3.X], then click OK, and
then Continue.


EsmeraldaHD:Operations:Instructions:PC Setup Packet:Dos/Win Install

5/28/97 BJM

  • The program will then warn that some network files could not
    be found. Select Scan, so the program can find the needed files.
    Then choose Yesand then OK.
  • If files can not be found, the network connection may have
    been broken. In this case, restart computer and begin Windows
    3.11 installation again.


6) Finish Windows installation:
*Select Continuefor the next several windows until the
window for setting up applications.Select Cancel.
*When prompted to view tutorial, select Skip Tutorial.
*Finally, select Return to MS-DOSto finish the installation and
to return to DOS.


7) Finish the Network Installation:
*Exit from Windows.
*Go to a: drive and type: a:\> install Card Type
*Follow the instructions from the DOS\Windows Network
Installation Procedure.


EsmeraldaHD:Operations:Instructions:PC Setup Packet:Dos/Win Install